landlord had a plumber in recently, I think they did it on purpose to slow down my water pressure). Use a 3/32'' allen wrench to loosen the set screw and remove the handle. Remove the two inlet screens. This image is not<\/b> licensed under the Creative Commons license applied to text content and some other images posted to the wikiHow website. If the aerator still gives you trouble, try buying another one from your local hardware store. wikiHow, Inc. is the copyright holder of this image under U.S. and international copyright laws. 9. Our Comment Box is provided by Countable Web Productions countable.ca, Click to Show or Hide Citations & References, POINT of USE BUILT-IN FIXTURE ANTI-SCALD VALVES, ANTI-SCALD WATER TEMPERATURE CONTROL TYPES, POINT of USE ANTI-SCALD WATER TEMPERATURE ADJUST Pfister, HOT WATER QUANTITY IMPROVEMENT via ANTI-SCALD VALVE, ANTI SCALD VALVE PROTECTION, Best Practices, WATER HEATER TEMPERATURE ADJUSTMENT CONTROLS, WATER HEATER TEMPERATURE TOO COLD or TOO HOT, Watts Series LF1170 and LFL1170 Hot Water Temperature Control Valves SPECIFICATIONS, Watts Series LF1170 and LFL1170 Hot Water Temperature Control Valves INSTALLATION INSTRUCTIONS, Domestic Hot Water Scald Burn Lawsuits, The Who, What, When, Why, Where, How, HOME INSPECTION EDUCATION COURSES (Canada), HOME INSPECTION EDUCATION: HOME STUDY COURSES, Pfister Faucets The Ultimate Explanation, How To Clear A Sink Drain With A Shop Vac? How to Slow the Waterfall Pressure of a Pond, How to Set Up a Home Jet Pump With a Pressure Tank. Apologies for the delay. Then turn the faucet control clockwise to the hottest position for one minute. If the problem has been solved, you will get warm water again after about an hour. Then view the full parts diagram to identify the correct part numbers to order. If your water department cant deliver more pressure and you have a 3/4-in. Remove the valve handleby removing the allen screw on the handle shaft. We and our partners use data for Personalised ads and content, ad and content measurement, audience insights and product development. This will help flush out any built up debris from your lines. To adjust the temperature supply remove the plastic cap on top of the valve and adjust with a close fitting spanner. 7. How to Replace Ceramic Disc Cartridges and Retainer Nuts on Pfister Single-Handle Kitchen Faucets. These photos are adapted from the Pfister tempeature adjustment video that is cited at the end of these notes. Fit a socket wrench over the adjustment nut on the top of the valve. 3633 I Street This article has been viewed 511,814 times. You can also use a lime cleaner like Formula 409. A: The 0X8-310A valve included in model #8P8-WS2-LRSGS can flow from the tub spout between 2.5 to 4.4 GPM, depending on the incoming pressure, type of installation, and spout trim. P.O. If there is no set screw hole, your handle will simply twist off. My original valve failed giving nothing but hot water at a very low pressure. This image is not<\/b> licensed under the Creative Commons license applied to text content and some other images posted to the wikiHow website. . While the supply lines are disconnected it is a good idea to flush them out before reconnecting. ), How To Mount A Ball Valve? Once you have identified the source of your problem, you may need to obtain replacement parts. 1 Unscrew the showerhead from the waterline. How do you adjust a thermostatic mixing valve? If the water stays cold, then youve turned off the right valve. If you are using a showerhead with a restrictor, you will need to make sure that you have the correct fittings for the type of restriction you wish to install. Philadelphia, PA 19134 Follow the steps below to help get your Pfister faucet back in working order. We can usually get you an answer within 24hrs. The lack of hot water is a common problem that can be resolved by looking for loose connections to the water heater and resetting any fuses in the circuit breaker box that may have tripped, causing a lack of hot water. 3. Make sure the shutoff valves near the water meter are fully open. [5] "Water Saving Tips: For Residential Water Use, Indoors and Out". But all three showers right next to tubs have much reduced flow. Reduced or No Water Flow on a Standard Open Spout. Amazon Link: https://amzn.to/3c3jrqEStore Link: https://www.amazon.com/shop/learningchords Feel and fit the handle, don't pound it into place. 10. The valves are auto mixers with set volume. You can do this by hand. POINT of USE ANTI-SCALD WATER TEMPERATURE ADJUST Pfister at InspectApedia.com - online encyclopedia of building & environmental inspection, testing, diagnosis, repair, & problem prevention advice. Remove the aerator or showerhead and make sure the debris screen is not clogged. or bigger copper or plastic water main coming into your house, consider installing a water pressure booster. The product model number (usually an 8 digit code, i.e. F-529-7AYY) is displayed on the product package and on the instruction manual right below the product name. Pull off the metal sleeve around the outside of the valve if the temperature adjustment is part of the valve cartridge. How do you adjust a Allen and Roth shower faucet? Turn the water supply back onand check the new tub or shower hot water temperature. This image is not<\/b> licensed under the Creative Commons license applied to text content and some other images posted to the wikiHow website. When youre finished, your faucet should run like new! Remove the two inlet screens. If cleaning the aerator did not improve the water flow we want to help you figure out why this is still happening. This image is not<\/b> licensed under the Creative Commons license applied to text content and some other images posted to the wikiHow website. If the handle has a lever, it's probably under the lever, and you can unscrew it with a hex wrench. Replace the cartridge, retainer ring (tighten down with adjustable wrench), and handle assembly. If they are difficult to remove by hand, you can use a small flat tool, such as a small flat head screwdriver to pull the screens out. If the water flow through the faucet is slow, the aerator may be plugged. This image may not be used by other entities without the express written consent of wikiHow, Inc.
\n<\/p>

\n<\/p><\/div>"}, {"smallUrl":"https:\/\/www.wikihow.com\/images\/thumb\/0\/0e\/Adjust-Faucet-Water-Pressure-Step-14.jpg\/v4-460px-Adjust-Faucet-Water-Pressure-Step-14.jpg","bigUrl":"\/images\/thumb\/0\/0e\/Adjust-Faucet-Water-Pressure-Step-14.jpg\/aid1318365-v4-728px-Adjust-Faucet-Water-Pressure-Step-14.jpg","smallWidth":460,"smallHeight":345,"bigWidth":728,"bigHeight":546,"licensing":"